# Config File for User-defined Instant Mappings # We assume that the controls on your MIDI controller # send CCs (except for pads). All controls that do not have # an explicit channel setting are expected to use the # global channel. CCs & Notes are counted from 0-127 # and channels from 0-15. [Globals] # The channel that the controller should send on GlobalChannel: 0 # If your controller is connected via USB, replace ControllerName # with the name of the respective port. Live will then try to # recognize the ports for you when you select your Instant-Mappings InputName: ControllerName OutputName: ControllerName # If your controller has pads that send notes, you can use them to # play the visible pads in your DrumRacks. Just replace the -1 for # the note (and channel) of the respective pad. The arrangement of # the pads in the DrumRacks is as follows: # 1 2 3 4 # 5 6 7 8 # 9 10 11 12 # 13 14 15 16 # (If you leave the channel of a pad at -1, Live will assume that # the pad uses the global channel) Pad1Note: -1 Pad2Note: -1 Pad3Note: -1 Pad4Note: -1 Pad5Note: -1 Pad6Note: -1 Pad7Note: -1 Pad8Note: -1 Pad9Note: -1 Pad10Note: -1 Pad11Note: -1 Pad12Note: -1 Pad13Note: -1 Pad14Note: -1 Pad15Note: -1 Pad16Note: -1 Pad1Channel: -1 Pad2Channel: -1 Pad3Channel: -1 Pad4Channel: -1 Pad5Channel: -1 Pad6Channel: -1 Pad7Channel: -1 Pad8Channel: -1 Pad9Channel: -1 Pad10Channel: -1 Pad11Channel: -1 Pad12Channel: -1 Pad13Channel: -1 Pad14Channel: -1 Pad15Channel: -1 Pad16Channel: -1 [DeviceControls] # The Encoders will control the device parameters (you can also # use knobs or sliders). Replace the -1's with the CCs sent by # the respective controls on your controller. You can also set # the channel for each controller if it differs from the global # channel (if you leave the channel of an encoder at -1, Live # will assume that the encoder uses the global channel). Encoder1: -1 Encoder2: -1 Encoder3: -1 Encoder4: -1 Encoder5: -1 Encoder6: -1 Encoder7: -1 Encoder8: -1 EncoderChannel1: -1 EncoderChannel2: -1 EncoderChannel3: -1 EncoderChannel4: -1 EncoderChannel5: -1 EncoderChannel6: -1 EncoderChannel7: -1 EncoderChannel8: -1 # Enter the respective map mode for the encoders here. The following # map modes are available: # - Absolute # - Absolute14Bit # - LinearSignedBit # - LinearSignedBit2 # - LinearTwoCompliment # - LinearBinaryOffset # - AccelSignedBit # - AccelSignedBit2 # - AccelTwoCompliment # - AccelBinaryOffset # Consult the controller's documentation to find out which mode to use. EncoderMapMode: Absolute # Buttons used here are expected to not be toggles (i.e., sending # value 0 every second time you press it). Bank1Button: -1 Bank2Button: -1 Bank3Button: -1 Bank4Button: -1 Bank5Button: -1 Bank6Button: -1 Bank7Button: -1 Bank8Button: -1 NextBankButton: -1 PrevBankButton: -1 LockButton: -1 [MixerControls] # Again enter the appropriate CCs for the respective controls. # If all sliders use the global channel to send their data, # you can leave the channels at -1. You can, of course, use # encoders or knobs instead of sliders. VolumeSlider1: -1 VolumeSlider2: -1 VolumeSlider3: -1 VolumeSlider4: -1 VolumeSlider5: -1 VolumeSlider6: -1 VolumeSlider7: -1 VolumeSlider8: -1 Slider1Channel: -1 Slider2Channel: -1 Slider3Channel: -1 Slider4Channel: -1 Slider5Channel: -1 Slider6Channel: -1 Slider7Channel: -1 Slider8Channel: -1 MasterVolumeSlider: -1 MasterSliderChannel: -1 Send1Knob1: -1 Send1Knob2: -1 Send1Knob3: -1 Send1Knob4: -1 Send1Knob5: -1 Send1Knob6: -1 Send1Knob7: -1 Send1Knob8: -1 Send2Knob1: -1 Send2Knob2: -1 Send2Knob3: -1 Send2Knob4: -1 Send2Knob5: -1 Send2Knob6: -1 Send2Knob7: -1 Send2Knob8: -1 TrackArmButton1: -1 TrackArmButton2: -1 TrackArmButton3: -1 TrackArmButton4: -1 TrackArmButton5: -1 TrackArmButton6: -1 TrackArmButton7: -1 TrackArmButton8: -1 VolumeMapMode: Absolute SendsMapMode: Absolute [TransportControls] # The transport buttons are also expected not to be toggles. StopButton: -1 PlayButton: -1 RecButton: -1 LoopButton: -1 RwdButton: -1 FfwdButton: -1